sewing

Tuesday, April 28, 2020

Sewing Tea Towels from Real Towels

Yes, I am looking for things to do every day while sheltering in at home.

I had taken my sewing machine out to sew masks and surgical caps for our local hospital, and knowing that I would not be going anywhere anytime soon, I left it out "in case" I wanted to sew something else.

However, the problem I encountered was that most of my sewing supplies and fabrics were either long gone to the local charity shop OR were already packed in one of the boxes in our basement and garage.

Ugh.

So, in desperation, I found a "seen better days" Turkish towel that could use a bit of a remake.

And remake it I did...

Into two tea towels for my kitchen.


I cut the towel into a large rectangle, approximately 25" by 19" unfinished.  

I then used an old trick to perfectly create corners.

I measured 1.5" from the corner of an index card, in both directions, and marked it with my pen.

I then measured 1.5" from the corner to the center and made a mark there as well.

I connected all the marks to make this tiny triangle.


Placing the corners and edges of the towel and triangle together, I folded over the towel to make a triangle on the edge.


I hit it with my hot iron to make a crease.


I removed the triangle template and set it aside to repeat on the other three corners of the fabric.


Using my scissors, I cut off the fabric triangle, making sure to leave a slight edge near the crease.


Now comes the easy part.

I gathered both sides of the towel and folded them over until the creases touched and created this sharp-pointed corner.

Can you see where this is going?


From here, I ironed a 1" fold all the way around the towel, making sure to do the exact same corner fold on each of the remaining three corners.


I didn't want to leave a raw edge, so I tucked under the 1" fold to create a 1/2" fold, ironing that all the way around the edges.


At the corners, the edge simply tucked itself away without adding additional bulk to either side of the toweling.


I used a pin to hold the two sides in place and then took it to my sewing machine.


My Brother sewing machine has some really fun stitches, so I decided to try out #41 using a black thread on the white toweling.


I lined up the folded hem in between the edges of the pressure foot and started sewing.


You can see the great vine pattern that emerged as I let the machine do its work.


At the corners, I simply stopped, lifted the pressure foot, turned my fabric, and proceeded down the next side of the towel.


When it was all done I had a great, decorative tea towel for NO MONEY and just a bit of my time.

This is a perfect project for even the beginner sewer as it just straight sewing and little skill knowledge.

You can make placemats and napkins using the same corner technique.

It was fun to continue to be creative when I can't get out to buy fabric right now.

I especially liked that I was able to repurpose most of the fabric from a towel that was going to end up in the trash otherwise.

It's great being resourceful in times like these!



Tuesday, October 22, 2019

Upcycling Thrifted Jeans

By now, you are probably aware that I love to sew, especially when I can refashion, recraft, or upcycle a thrifted garment.

Today, I am going to share how I took a pair of $4.50 thrifted jeans, some fabric that I had on hand, and simple sewing skills to create an easy bag that I take back and forth to the gym.

Let's get started.


Here are my jeans and fabric that I matched from my stash.

The large floral is from a collection of companion colorways that I purchased from a local fabric outlet for $2.00.  


The jeans were from a local "Teen Challenge Thrift Shop" that I love to visit weekly.

They have great housewares and decor, and rows of clothing items.  I grabbed 2 pairs of jeans a while back and used the darker pair for this project.


I started by using bulldog clips at the top of the jeans so that the waistband was even all the way around.

This was important because worn jeans tend to "slip" in the front.  If I had cut them without doing this, I would have had an uneven back and front length.


Next, I needed to slice up the inside seam, through the crotch area and back down the other leg.


I used a sharp pair of shears to cut as close to but not on the rolled seam.  You can see that on typical jeans the inside seam is rolled over and then sewn.


Once this was done, I folded over the front part of the crotch seam to make the jean fabric flatten against itself.

Pants are cut on curves because if you took a side cross-section of your body, there is a curve from the lower back down through the crotch area up to the belly.

You cannot just sew a cut crotch seam without cutting up into both the front and back of the pants.


So, using those same sharp scissors, I cut up the front seam to the point where the jeans would lay flat on itself.


See?

That point is actually the center of the crotch on the jeans.

Now the front part of the jeans lays flat.


I repeated that same process with the back of the jeans as well.


Where the two legs meet (finger) is where the bottom of my bag will be sewn.


Using a ruler and a black pen, I marked that on the front side only and then cut straight across through both the back and front layers.


Here's the result.

Can you see the bag starting to form?

(You can also follow these same steps to create a jean mini-skirt as well...)


Using pins to secure the left and right sides to each other, I sewed a seam from my finger down to the bottom.

I followed the curves of the top layer so that you cannot see the blue thread of the seam.


I did the same thing in the back.


Next, I sewed the front pocket lining down on the edges so that they did not pull inside out once the bag was finished.


From the outside of the pocket, you can't even see the seam because the thread blends so well with the jean fabric.

At this point, I removed the bulldog clips, turned the jeans inside out and sewed a seam at the bottom of the two sides.

I now had a bag, BUT I wanted to create a "real boxed bottom."

This is easy to do on any bag.


I measured the bottom seam from the edge (point) at 3 inches and made a mark.


I folded the seam open so that it forms this triangular section.

I drew a straight line from side to side as a guideline for my seam and then put fabric to needle.


This is the result.

A boxed bottom to my bag.


Now I needed to make two handles.

I took one of the legs and cut two even length pieces that were 4 inches wide.

(I'm keeping the other leg for a future project)


I folded each side over an inch, meeting their raw edges in the middle to the strap.


Next, I folded in the middle so that the original folds met together.

This means that you never have to make a "tube" of fabric then turn it inside out!


I sewed two seams down each side about a quarter of an inch apart.

This gave my strap a bit of stability and stiffness.

I set them aside and got to work on creating the inside lining with the floral fabric.


I knew that this fabric was not quite enough yardage front top to bottom to fill the inside.

To make it work, I added a blue strip to each side's top area.  This gave me the added length that I needed.


I sewed them together then "stitched in the ditch" (which means to stitch along the seam from the right side to hold the fabric flat) as a finish to the lining edges.


I created a small interior pocket and stitched it to the lining on one side.


I topped that with a bit of a coordinating fabric as well.

I sewed down both sides and across the bottom of the lining to create a "bag/lining" to go inside my jean bag.

I boxed the bottom exactly like I did the jean bag.


Now it was time to place the lining inside the jean bag.

Keeping both bags, as shown above, I placed the lining inside, matching the top edges.


I started by placing clips at certain points on both bags.

It's easy to explain it like a clock.

I placed a clip at 12 and 6 o'clock so that my lining front and back met up exactly with the front and back of the jean portion of the bag.

Then, I clipped at 3 and 9 o'clock where the seams of both bags met together.

This left me to work between those clips and evenly distribute the lining and the jean bag.


I now placed one end of a strap where I wanted it to be in relation to the front of the jean bag.

I "sandwiched" it between the jean portion and the lining, and then used clips to hold it in place.

I took the other end of that same strap and repeated this process on the other side of the front.  I made sure the strap was straight from one side to the other.  I matched this strap placement on the back of the bag as well.

I used the bulldog clips to hold the jean fly together as there were two layers of fabric plus the lining.

Prior to sewing, I made sure the bag hung at a point the was comfortable on my shoulder.


I now took this whole thing to my machine and slowly stitched about an eighth of an inch down from the edge, through all the layers of fabric, all the way around.


Super easy when you take your time.

Especially when you have this at the end...



An upcycled jean bag!

It has both the front and back pockets from the jeans.  One is perfect for housing the lock that I use in the gym locker room.

The bag holds my lifting gloves, some essential oils I used when working out, my notebook, my headphones, a spare glasses case (to hold my glasses during yoga), and any other items I might need for the gym.

I've clipped my gym swipe card to the belt buckle and add my car keys when it's in the locker.

It's dedicated just for the gym, but could easily be used as a purse or bag for another purpose as well.

It's a great "rule breaker!"



Tuesday, October 15, 2019

Wear It Again...Sam

Because I love to get as much wear out of my clothing, I often "refashion" pieces to update their style.

Sometimes, I even "refashion" because while the fit is perfect in one place, it's lacking in another.

Fortunately, I had a grandmother who sewed, and she taught me much of what I know today.

Here's 2 items that have a new lease on life.

First, let's start with this unworn purchase.


While camping near West Point, we visited the campus and I purchased this pull-over.

It's perfect for throwing over jeans and hanging out, BUT, the sleeves were just too long.

Even if I rolled them up, the fabric was too "slick" for them to stay that way.

I needed to shorten the sleeves so I could wear this comfortably.


This first thing I did was try it on and pin one sleeve at the point where I wanted the bottom cuff to hang on my arm.

You can see where the pin is compared to the cuff.  It was obviously for someone who has orangutan arms...especially because I don't have short arms what so ever.


I made a mark about a quarter of an inch down from the pin.  This will be my seam allowance. 


I used that cut piece as a guide for the other arm, lining it up and cutting that side off as well.

I could have just hemmed that length, BUT, I wanted to have the cuffs that were originally on the garment.


So, I cut both of them off (carefully making sure to get the correct cuffs on their respective sides), again, giving myself a quarter inch seam allowance.


Now, because I had to cut up quite a bit on the sleeve length, I had more fabric there than on the cuff.

Here's a comparison of the cuff (bottom) against the sleeve (top).  That's a good 2 inches or more around.

But not to worry, here's where some crafty pleats come in handy.


I placed right sides together inside the sleeve, matching up the seams under the arm of the garment.


I worked around both the right and left sides until I had pinned all parts of the cuff to the sleeve.

This is where you can really see how much shorter the cuff was than the sleeve.


When flattened, there is a natural fold in the sleeve to the right of my finger. 

I took that fold and lined it up with the fold of the cuff that's showing to the left of my finger, just inside the sleeve.

I matched those folds, then added a pin to keep both of the folds together.


This creates a "pinch" or wave in the remaining extra fabric of the sleeve, which allows me to create an even pleat on both sides.


I folded one pleat to the bottom as shown here, and one pleat to the top.


Here's what it looks like inside the sleeve.


Because I know that these pleats can sometimes get skewed when sewing on the machine, I pinned down the folds to keep them nice and neat.


I repeated this process to the other sleeve and got ready to run this through my machine on a straight stitch.

I ran one seam on the inside and folded the cuff out.


I then ran a "stitch in the ditch" on the outside so that the cuff laid down nicely with the sleeve.

As "stitch in the ditch" is a seam that is sewn right into a natural seam already present.  I'm pointing to it here on the sleeve and cuff.


Now, I had a shortened sleeve with a nice pleat that looked like it was always this way.


Here is my finished garment.  I like that that little bit of pleating makes it more feminine.

The next garment was this LuLaRoe Carly dress that I have had for a few years, but the hi-lo hem was so out of style and I was just not wearing it.

However, I still liked the wavy fabric, it's incredibly soft and flowy, and the black and white pattern is so easy to pair with many colors.


It's rare that I wear a dress in retirement, and this would not be one the I would reach for if I needed a dress from my closet.

But, I would still wear it if it was shortened into a top.

So, that's what I did!


I carefully folded the dress in half lengthwise, making sure that I lined up the shoulders, arms, and side seams as perfectly as I could.


Using a top that I wear often and like it's length, I carefully laid it out over the dress.

I lined up the shoulders and side fold of the top with the dress.


This creates an even guide for the length I want the top to be when hemmed.

Cutting about a half inch down from the top's hem, I drastically shortened the dress.


You could mark it, but I just eye-balled it across as I cut.


I now had the perfect length, including a bit extra for the rolled hem.

I kept that excess fabric.  You never know when it might come in handy for a future project.


I rolled the fabric over twice to make about a quarter inch hem.  Because this is a cotton knit, it "rolls" beautifully and sets into the hem quite easily.


I used a medium-wide zig-zag stitch to sew the hem closed and this refashion was done in under 15 minutes.


Now I have a "new" to me top to wear this fall season, adding a sweater if it's a bit chilly.

If you do not sew, check with your local dry cleaners.  Usually, they have an on staff seamstress who can do all of this for you for a reasonable price.

When you are wondering what to wear, and you're passing by some great garments in your closet because of poor fit or style issues, take another look at them.

Perhaps just a few adjustments you can give them new life, and "Wear them again...Sam." (no offense to Humphrey Bogart.)

It's a great rule-breaker!











© No Rules after 50. Made with love by The Dutch Lady Designs.